Chassis

• Mercedes-Benz UNIMOG
• UNIMOG heavy duty chassis
• Wheel base 3850 mm (12´8´´)
• GVWR: 11900 kg (26000 lbs)
• U-section frame
• Torsional flexible load carrying frame
• Cross country ratio transmission
• Additional gearbox with crawler gears for hill climbing capacity over 100% grade
• All gears usable both forward and reverse
• Four wheel drive can be selected while driving
• Differential locks for both front and rear axle, can be selected while driving
• Fully protected drive train using torque tube technology
• High mounted gear transmission
• High ramp breakover angle
• Portal axels for high axle ground clearance
• Front and rear tires follow same track
• Enhanced driving safety using coil springs, shock absorbers and stabilizers both front and rear
• Four wheel disk brakes
• Enhanced water fording capacity with raised engine air intake and vent openings
• Torsion free drivers cab mounting using 3 point kinematic mount
• Soundproofed and viabration isolated drivers cab
• Raised drivers cab ceiling for additional equipment space and spare tire storage
• Hydraulic power steering
• Air brakes and power assisted clutch
• Engine compartment easily serviced from exterior hood
• Manual hydraulic drivers cab tilt
• Low emmision turbo diesel engine
• Engine oil lubrication system designed for extreme tilt and slope
• Engine enclosure for lower noise emission

Body Unit

Frame assembly
• Mercedes-Benz approved, low 3 point kinematic attachment with main and flex mounts for stress free body coupling to the torsion elastic chassis frame
  
  Body unit construction
• Self supporting UNICAT sandwich plate panels of fibre glass composite (corrosion free)
• Panel connections made by adhesive bond to custom extrusions eliminates metalic heat conduction paths
• Matched thermal coeficients of expansion prevent distortion with changes in temperature
• Wall thickness 60 mm (2,36´´) with polyurethane foam insulation, 3 mm (0,12´´) FRP outer surface, 2 mm (0,08´´) FRP inner surface
• Ins. rating 0,44 W/m² K (0,078 btu/ft² h degF)
• Bottem panel at 95 mm (3,7´´) thickness. Compound construction of plywood bottom, foam body, integrated welded steel frame and surfaces of FRP
  
  Access to drivers cab
• Highly flexible waterproof bellows coupling
  
  Doors and hatches
• UNICAT door and storage hatches constructed of fibreglass composite plates and frames
• Thickness of door 60 mm (2,36´´)
• Double sealed doors and panels
• Heavy duty locks with seal compression
• Stainless steel hinges throughout
• Additional retractable bolts at top and bottom of doors
• Safety cylinder locks all keyed alike
  
  Windows and skylights
• UNICAT burglarproof, scratchproof sidelights and skylights
• UNICAT window frame made of extrusions, coldspot and corrosion free
• Double insulated thermal security window glass

Interior Lay Out

Seating Unit
• Seating unit mounted on pedastel
  
  Office place
• Desk with integrated PC and printer
• Swivel chair for office place or seating unit
  
  Beds
• 2 single beds in the back fitted with comfortable mattresses and duckboards
• Size: 80 x 206 / 181 cm (2´7´´ x 6´7´´ / 5´11´´)
  
  Shower and wash room
• Shower in entrance way with combined door, to seperate either from toilette or livingroom
• Table with integrated sink
  
  Toilet
• Seperated toiletroom
• Also usable as drystorage due to is own radiator
  
  Kitchen
• Diesel powered ceramic stove
• Conventional/microwave oven
• Household size stainless steel sink with single handle faucet
• 100 l (22 gallons) fridge
• 40 l (8,8 gallons) deep freezer box
• Kitchen closet with drawers
• Hanger closets with halogenlamps
  
  Storage
• Storage space at the office place
• Hanger clothing closet with pull-out hanger bar
• Storage cabinet with drawers under the bed
• Linen cupboard with drawers
• Hanger closets over the beds
• Outside storage cabinets under the two beds
  
  Workmanship
• All furniture is custom built to the highest cabinetmaking standard out of wood core plywood using heavy duty locks and hinges
• Materials and finishes may be specified by customer
  
  Lay out
• Design and color of floor, walls, ceiling and upholstery may be chosen by the customer
• Walls and ceiling are painted with multiple coats

Technical equipment

Electrical equipment
• Custom control panel to control power management and liquide storages
• Battery main switch, savety cutout, fault current breaker
• DC power supply by battery bank, automatic I-U regulated alternator and AC automatic I-U shore charger with cell temperature sensing
• Inverter for 120/240 V
• Power plugs for 12 V, 120/240 V and 400 V
• Pre wired for solar system
• Pre wired for TV, video and music system
  
  Generator
• Watercooled diesel generator, remote controlled
• Raised exhaust and air intake system
• Water fording capacity due to overpressure system
• AC and rotary current , power 4 kVA
  
  Lighting
• Integrated low voltage quartz halogen lights over the table, office place, kitchen, hall way, shower, toilette and storage area
  
  Water supply
• 440 l (97 gallons) freeze proof drinking water tanks
• 22 l (5 gallons) hot water-heat exchanger
• Stainless steel freeze proof waste water tank
• Water faucets in both bath and kitchen have removable sprayers
• All components are built due to highest household quality standards
• All plumbing is insulated to prevent freezing
  
  Toilet
• Porcelain-vacuum toilet with water flushing
• Stainless steel, freeze proof sewage holding tank
  
  Heating system
• 4 stage diesel/electric-motor lost heat powered warm water central heating (2 x 5 kW) with engine and diesel preheating system
• Waste and sewage holding tank heating
• Radiators in living and bath area
• Antifrost system